Getting the decals off, and why
Alas, the old Maritime 20 I bought last fall is still a driveway boat, but I’d like to think that Junior will look sharp when it does launch. I extended the black trim paint to the dash — and have almost finished all new wiring and electronics (and am excited about testing that Humminbird Solix 10) — but to my eye, the good looks of the Maritime and Evenrude E-Tec designs really popped when the branding decals came off. Getting some of them off wasn’t easy, however, so I’ll share what I learned.
A plastic razor blade is my normal go-to tool for removing decals without messing up the underlying gel coat or paint. And if scraping up a decal’s edge and then finger pulling it off with even pressure at a very low angle doesn’t work well, I try softening it up first with a heat gun. Alternatively, an acetone-based product like Goof Off can be used to “loosen” the decal’s grip, or at least to remove any remaining adhesive.
But I am certainly not a de-decaling expert, and my first attempt at the white “Maritime Skiff” logo on Junior’s house side ended with loud swear words. I had gotten enough off that I was fully committed, but the task was extremely slow going even with extreme heat. I wasn’t surprised that Maritime used quality decals and applied them well — this boat is solidly built in every way — but I had not realized how 20 seasons of exposure could apparently make the adhesive even more tenacious while leaving the plastic more brittle and breakable.
I had created a problem! So I searched the Internet hoping to find a better solution, and that’s where I discovered a world of decal erasures like that ABN 4-inch disk seen above.
The wheel works like a big pencil erasure, the friction of soft rubber grabbing the decal plastic and adhesive. In fact, the process works with even less rpms than I was using in the video, generates very little heat (that could possibly damage the gel coat), and I was only wearing the mask for the benefit of my friend Alden manning the phone camera. The erasure and decal debris tend to fall away or hang on the boat until wiped off.
I estimate that removing these particularly hearty 20-year-old boat decals was 10 times faster with the $10 erasure wheel than with the heat gun process that’s worked for me in the past, and that was good news worth sharing.
I was not trying to illustrate the dangers of a heat gun, but I did indeed hold one to that dimpled spot a little too long when removing the Furuno decals (that were about ten years old). I wouldn’t use the erasure disk on the more delicate radome cover, but maybe I should have tried harder with blade and Goof Off (or another chemical solution, anyone?). And I’ll add that the big decals on the almost new E-Tec came off pretty easily without a heat gun, a further indication that age can make for significant differences.
But why remove the decals anyway? There is no practical reason I know of, and actually I’ve been told that it reduces the resale value of an outboard motor. And in my case — unlike, say, when my dad glued plastic half lemons to the doors of a displeasing station wagon — I’m quite pleased to own the Maritime, Evinrude, and Furuno brands involved. So it’s a “beauty in the eyes of a beholder” sort of thing and maybe a regional preference given the numerous classic yachts looking good around here with all brand names expensively painted out.
Getting back to Junior, note the custom antenna plate recently shown with its Sirius Signal C-1002 eVDSD holder, but now fully installed. Also note the ACR RCL-85 LED searchlight, which I’m tentatively delighted with (and which does not come with any decals applied). Is this little boat looking sharp or what?
And what about my other boat? Junior projects were delayed while I got Gizmo at least minimally ready for launch on Tuesday, and while the elaborate electronics redo remains largely in my mind, I did get a thrill on the ride up to Camden yesterday. In January, my long beloved Volvo mechanic/technician Pat Ricci did everything he thought necessary for Gizmo’s TAMD74C-A at 20 years old and 3,500 hours of use, and behold the results. In my 10 years of ownership, I’ve never seen the boat go over 19.5 knots before (and the exhaust looked clean).
I like to see older things get new life, and that also applies to Gizmo’s Firefly battery bank, which are acting like spring chickens after a series of restoration charges (that I will detail soon). And I smile as I find myself an old boat guy, now with two 20-year-olds, who still can’t reasonably estimate how long projects will take.
Panbo test fleet adds a fast outboard: Gizmo Junior
October 14, 2019
Heat shrink solder sleeve butt connectors, great for skinny boat wires
May 24, 2019
Gizmo found, Web the hero!
July 5, 2006
Fanless On Board PC
July 29, 2004