Shakespeare’s ART-3, check your transmitting power!

Shakespeare ART3 copyright PANBO BE

I may be naive–I don’t have much experience with testing tools–but Shakespeare’s ART-3 impressed me. In this picture, bigger here, that VSWR reading well into the red demonstrates something I’d suspected but wasn’t positive about…the old antenna attached to the Icom 504 may look OK but it must be pretty pooched inside. VSWR, by the way, stands for “voltage standing wave ratio” though Shakespeare more reasonably terms it “antenna efficiency”. Interestingly the meter showed the Icom and other of my test radios transmitting at a mere 17 watts with this same antenna, but pumping out a full 25 watts with a VSWR of only 1.25 (a mere loss of 2% according to the table on the meter face) when well wired to a decent antenna. Antennas really make a performance difference, as does a good power supply. The $90 (retail, though I don’t see a place to buy one online) ART-3 can also generate a tone on Channel 72, thus providing a simple reception test. Note that you do need to provide your own short patch cable between the meter and radio, annoying, but it is smartly designed so that it can be used portably with an internal battery or rigged permanently with wired 12v power.

PS, 3/12/2011: Valuable discussion about what a meter like the ART-3 can, and can not, determine following this entry.

Similar Posts:


Shakespeare VTronix YHK Sailboat Antenna
March 9, 2011

The Wizard, first impressions
October 28, 2008

Icom IC-M73 Plus with ‘rewind’ & more in VHF
January 30, 2013

The Big Screen
June 7, 2004

Ben Ellison

Ben Ellison

Panbo editor, publisher & chief bottlewasher from 4/2005 until 8/2018, and now excited to have Ben Stein as very able publisher, webmaster, and editing colleague. Panbo is going to the next level in 2019 and beyond.

8 Responses

  1. Russ says:

    Look interesting. I Googled it and found it for $60 at Boatfix.com. I’d really like this for my SSB!

  2. Jim Hebert Jim Hebert says:

    If that is a VSWR reading, something is terribly wrong. Are you sure you set the meter properly for the VSWR measurement. It looks like you need to adjust the sensitivity using the knob and the SET position.

  3. Ben Ellison Ben Ellison says:

    Really, Jim, that is the VSWR. I adjusted sensitivity to the Set line before measuring, per instructions; also got similar results with other radios and same antenna, much better results with same radios and new antenna. I had noticed many months ago that this antenna doesn’t work well at all! Maybe it’s something as major as a broken lead inside the coax?

  4. Pat Harman says:

    I bought my meter at Fisheries Supply in Seattle.
    http://www.fisheriessupply.com
    It is a useful tool, and comes with the jumper cable.
    Fisheries Supply also carries the Morad “Hot Rod” antenna. This is a MIL spec VHF Antenna much used by the commercial fleet which will cost about $150 as you need addapters to mount it.
    I also recommend using soldered connectors with antennas, this saves a lot of grief.
    I am retired and have no interest, except in gear that works.
    Pat Harman

  5. bob says:

    VSWR can be calculate by the following:
    F = Forward power
    R = Reflected Power
    VSWR = (F+R) / (F-R)
    If everything is ideal you have no reflected power, its all going out the antenna and you have F/F = 1
    It all goes down hill from there 🙂
    bob

  6. James says:

    This would be great for SSB, anyone got a good way to test SSB antenna or longwire antenna?

  7. Bart Browning says:

    I noticed that the ART-3 has a frequency range of 155-158 Mhz. I need to us this at the frequency of 158.770. Just wondering if the accuracy will be degraded because it is on the extreem high end of the frequency range? I couldn’t tell if there are any interchangeable crystals.

  8. flucklimi says:

    Всем, кто не потерял надежду найти своего принца на Западе
    Расскажет и научит вас вебсайт http://www.mydatelove.com

Join the conversation

Your email address will not be published.